Ansible for Network Engineers-Quick Start with GNS3, Ansible and Network Automation – David Bombal

Salepage link: At HERE. Archive:

~~$40~~ $18 – Ansible for Network Engineers-Quick Start with GNS3, Ansible and Network Automation – David Bombal

Learn Network Automation with GNS3 and Ansible.

Do you want to program networks using Ansible, but not sure where to start? Well, this course will show you how you can start programming Cisco networks within 30 minutes.

This course was created for network engineers. There are too many other Ansible courses out there that try to make network engineers server administrators. They concentrate on server administration, installation of software packages and other server admin tasks.

This course is different.

This course is practical. I won’t talk about programming in abstract terms and make you wait before you can start automating networks. I will show you how you can quickly and easily start network programming by using GNS3, Cisco IOS and Ansible.

You will see demonstrations of the configuration of both Cisco routers and switches in GNS3. For example, how to configure multiple VLANs on a multiple switches, or how to configure OSPF on a router and more much more.

Learn how you can use Ansible to troubleshoot networks! Use a single Ansible command to retrieve mac address table information from multiple switches in seconds. Then pipe the output to a regular expression to filter down to a single MAC address.You will never troubleshoot networks the same way again!

This course shows you practical examples of using Ansible to programmatically configure Cisco network devices rather then just talking about it.

The days of configuring Cisco networks only with the command line interface (CLI) are drawing to a close. You need to add network programmability using Ansible to your skill set.

Learn how to automate networks using:

SSH
Ansible Network modules
Ansible Playbooks
Ansible ad hoc commands

Don’t reinvent the wheel. Use the tools available to you to quickly and easily automate your networks.

GNS3 Academy Curriculum

Welcome

Welcome! (9:02)
Good and bad news
Answering your questions (1:53)

GNS3 2.1 Install

GNS3 2.1 Install Part 1: Components and software requirements (3:32)
GNS3 2.1 Install Part 2: GUI install (11:47)
GNS3 2.1 Install Part 3: Troubleshooting GNS3 installation issues Windows 10 (4:37)
GNS3 2.1 Install Part 4: Basic GNS3 Network (your first network) (9:50)
GNS3 2.1 Install Part 5: Where do I get Cisco IOS images? (7:55)
GNS3 2.1 Install Part 6: Cisco IOS network using Dynamips (12:13)
GNS3 2.1 Install Part 7: GNS3 VM, VIRL and switching (8:29)
GNS3 2.1 Install Part 8: GNS3 VM, VMware 14 issues (11:55)
GNS3 2.1 Install Part 9: Cisco VIRL IOSv import into GNS3 (11:23)
GNS3 2.1 Install Part 10: Cisco VIRL and Dynamips network! (7:47)

Ansible Quick Start – your first playbook (configure router)

GNS3 Installation and Setup
GNS3 Initial Setup (4:09)
Setup SSH and view ansible.cfg settings (3:55)
Configure hosts (4:02)
ansible.cfg (2:30)

Ansible Quick Start: Ad hoc commands

Ad hoc Ansible Introduction (1:29)
Ad hoc Ansible Part 1 (6:09)
Ad hoc Ansible Part 2 (9:29)
Ad hoc Ansible Part 3 (3:07)
Ad hoc Ansible Part 4 (6:07)
Ad hoc Ansible Part 5 (1:18)

Ansible Quick Start: Raw Playbooks and Cisco IOS Command module Playbooks

Playbook to retrieve ARP cache (4:49)
Playbook to retrieve MAC address tables (2:34)
Playbooks using Cisco IOS command (3:05)
Playbooks using Cisco IOS command – show version save to file (3:48)
Playbooks using Cisco IOS command – show run save to file (2:43)

Ansible Playbook – CLI playbook

Ansible CLI playbook (1:02)
Run playbook (7:25)
Multiple devices (9:30)
Multiple Plays (6:29)

Ansible Quick Start: Playbooks and Cisco IOS Config module

Import GNS3 project and verify networking (3:39)
Cisco IOS Config Playbook 1 (10:09)
Cisco IOS Config Playbook 2 (3:22)
Cisco IOS Config Playbook 3 (6:38)
Cisco IOS Config Playbook 4 (4:59)